2SD2634 DATASHEET PDF

2SD Features. High speed. High breakdown voltage(VCBO=V). High reliability(Adoption of HVP process). Adoption of MBIT process. On-chip. 2SD datasheet, 2SD circuit, 2SD data sheet: SANYO – Color TV Horizontal Deflection Output Applications,alldatasheet, datasheet, Datasheet. datasheet search, datasheets, Datasheet search site for Electronic Components and 2SD Datasheet(PDF) 1 Page – Sanyo Semicon Device.

Author: Galar Shaktirg
Country: Cameroon
Language: English (Spanish)
Genre: Relationship
Published (Last): 20 November 2013
Pages: 267
PDF File Size: 5.52 Mb
ePub File Size: 7.17 Mb
ISBN: 889-5-94761-354-5
Downloads: 8024
Price: Free* [*Free Regsitration Required]
Uploader: Voodoomi

Do not disconnect the antenna or the power cord during a heavy storm. If there is permanent datadheet such as a damaged circuit, power cannot be restored and the circuit will have to be repaired.

All voltages are in V. Apague siempre el aparato cuando no lo utilice. Parts specified with “X” are not installed in this model. If you are not sure of the type of electrical power supplied to your home, consult your dealer or local power company. Apague el televisor y espere que el tiempo mejore.

Learn More — opens in a new window or tab Any international postage is paid in part to Pitney Bowes Inc. Excepting electrolytic capacitors, all capacitance values of less than 1 are expressed in F and more than 1 are pF.

Contact the seller — opens in a new window or tab and request post to your location. Watch list is full. Press daatsheet or 4 on the Remote Commander to select dtaasheet item.

  DMP XR100 PDF

Service manual | KV-25FS120 – Philips Home

When something abnormality occurs during TV reception, the TV set goes to the stand-by mode. Replace only with part number specified. Discharge the anode of the CRT and remove the anode cap. To ensure reliable operation of the set, and to protect it from overheating, these slots and openings must never be blocked or covered. STAT magnet b 2.

Power supply will shut down when waveform interval exceeds 2 seconds. If landing at the corner is not right, adjust by using the disk magnets.

2SD datasheet, Pinout ,application circuits Silicon NPN Power Transistors

Readjustment should be made only after picture tube or deflection yoke replacement, following the steps below: Unplug all interconnecting leads from the deflection yoke, neck datashet, degaussing coils and CRT grounding strap.

Components indicated by a! Install the set on a stable, level surface.

Method of Setting the Service Adjustment Mode Diagnostic Item Description Power does not turn on No. Read more about the condition. STAT magnet is moved in the direction of arrow a and b, red, green, and blue dots move as shown below: If you will be controlling all channel selection through your cable box, you should consider using the Channel Fix feature by setting your TV to channel 3 or datashedt see page After removing the anode cap, short circuit the anode of the picture tube and the anode cap to either the metal chassis, CRT shield, or carbon painted on the CRT.

  BEHRINGER BTR 2000 PDF

If you are 2sd264 to insert the plug fully into the outlet, try reversing the plug. Do not place any objects, especially heavy objects, on top of the set. Replace these components with Sony parts whose part numbers appear as shown in this manual or in supplements published by Sony. The reading should be zero ohms. Be sure that you have not connected the digital cable box to the TV’s jack. Waveform were taken with PAL colour bar and controls adjusted for normal picture.

DC Power Supply 4. Adjust the value of HPOS with 3 and 6 for the best horizontal center. The CRT 2sd263 the time being adjusted.

SYNC is more than seven verticals in a period, the unit will automatically turn off. Parts specified with “J” are just jumper wires. Voltage readings take with a “VTVM” are from point indicated chassis ground.

Red BlueFigure 7 Adjust the angle and rotation of tabs 3 and 4 eatasheet align the vertical and horizontal lines. Slope Vertical shift ItemVert.

Adjust vertical red and blue convergence with V.